Toy Pictures

[toy001.jpg]	The tyvek(tm) flogger. When I use this one, people look over to see who is being murdered only to see the bottom giggling. It sounds very mean but is extremely gentle. Autoclavable. Neads ironing ocassionally as the tails tend to fold over each other with use; this reduces the thunder. All bark and no bite. This flogger is hard on the top because it is swung FULL force.
[toy002.jpg]	This is a simple flogger made from polyester clothesline and a gel-grip bicycle handle. Autoclavable.
[toy003.jpg]	Ball Chain flogger. Use with ice water or a violet wand or flog lightly. Made with 8" stainless steel eyebolt, ball chain, and a piece of heat shrink tubing. Autoclavable.
[toy004.jpg]	Silicone Rubber Tailed Flogger. Stings like a sunofabitch. Autoclavable.
[toy005.jpg]	Another picture of the silicone tailed flogger.
[toy006.jpg]	Heavy nylon twine flogger. Handle whipped and dipped, no core. Very Thuddy and pretty quiet. Autoclavable.
[toy007.jpg]	This is a flogger made from multiple colors of polyester ribbon. Actually, this one stings a bit. Handle is an 8" stainless steel marine eyebolt. Dipped. Autoclavable but the colors will bleed a little.
[toy008.jpg]	The Spandex Flogger. Delivers a light thud. Autoclavable. Slit a sheet of 24"x60" spandex into 1"x18" tails. Wrap the unslit portion around a 8" stainless steel marine eyebolt using silicone dip as an adhesive between layers. Secure the top layer in place with pins and wire ties; when it cures, remove the pins and wireties and dip in silicone dip.
[toy009.jpg]	A light nylon twine flogger. Whipped and dipped. Autoclavable.
[toy010.jpg]	A light nylon twine flogger made from a 260 foot roll of black #18 twine. Whipped and dipped. Autoclavable. Ranges from extremely sensual to light sting; good for initial warmup.
[toy011.jpg]	Another silicone tailed flogger. Strands were braided around an 8" stainless steel marine eyebolt and then dipped. Autoclavable.
[toy012.jpg]	A cane. Made from a fiberglass rod from a driveway marker. One end was rounded and dipped in silicone. A loop of nylon cable tie material was folded over the other end to make a hanging loop and then nylon twine was whipped over the cable tie and the rest of the handle area. Handle and eye were dipped in silicone dip. Theoretically autoclavable if you have a big enough 'clave.
[toy013.jpg]	Heavy multicolored tail flogger. This was made from two boxes of five rolls of florescent colored twine (Lehigh Flying Colors) obtained from Lowes Hardware (near the rope and chain). Handle whipped and dipped, no core. Each spool was 160 feet of approximately #18 twine; the five colors were green, yellow, orange, pink, and gold. 1600 feet of twine total. 800 tails will unravel to 2400 during first use; each of those tails contains a couple dozen strands which will slowly unravel as well. Fairly quiet. Ranges from sensual to thuddy. Total length is around 24 inches and it weighs around one pound. Autoclavable.
[toy014.jpg]	A light multicolored twine flogger. This was made from 1/2 box of the lehigh flying colors twine. Sensual warmup use. Autoclavable.
[toy015.jpg]	Braided nylon rope flogger with silicone dipped tips to prevent unravelling. Handle wipped in twine and dipped, no core. This is very stingy due to the rubber tips. Autoclavable.
[toy016.jpg]	A latigo shoelace flogger. Wipped with twine but not dipped, so you can see how the handle and the eye were whipped separately. Do not autoclave.
[toy017.jpg]	A suede flogger. This was made from a small 8-1/2x11 craft store piece of suede, a piece of dowel rod, and upholstery tacks. Do not autoclave.
[toy018.jpg]	Another shoelace flogger. Do not autoclave.
[toy019.jpg]	Bicycle innertube flogger. Wooden dowel core. Upholstery tacks. Might survive occasional trips through the autoclave.
[toy020.jpg]	Chamois flogger. This was made from a piece of Chamois (Pronounced shammy) sold for polishing cars, a piece of wooden dowel, and a hacksaw. Do not autoclave.
[toy021.jpg]	Another cane picture (see description above).
[toy022.jpg]	Closeup of the cane handle.
[toy023.jpg]	Steel spreader bar. Adjustable. Ok for suspension. The perforated tube is sold in the hardware store near the angle iron and threaded rod. 5/16" eyebolts.
[toy024.jpg]	A sheet of tyvek being slit to make a flogger. This is also how the chamois and suede floggers were slit.
[toy025.jpg]	Homemade exam/massage/bondage table. 1st generation.
[toy026.jpg]	Various views of ceiling mounted strut grid. Made with superstut/kendorf.
[toy027.jpg]
[toy028.jpg]
[toy029.jpg]
[toy030.jpg]
[toy031.jpg]
[toy032.jpg]
[toy033.jpg]
[toy034.jpg]

[an error occurred while processing this directive]

MyBDSM.COM FREE Webpages for the BDSM Community